This site has limited support for your browser. We recommend switching to Edge, Chrome, Safari, or Firefox.

Shopping Cart

Your cart is empty

Continue Shopping

Recreation Terpene Effect Blend

$10.00

The terpene profile in our Recreation Broad Spectrum Effect Blend is a blend of terpenes designed to impart an energetic, uplifting effect. When combined this blend provides the perfect synergy to be active.

This product does not contain any THC, CBD, or any other active cannabinoids.

Size:

Volume:

Mass:

Click an icon to learn more

Alpha-Pinene, Beta-Pinene, Beta-Caryophyllene, D-Limonene, Terpinolene

To create this blend, we've used these key terpenes. This is only a partial list of the blend's formulation; each blend actually contains far more isolates. They contain no THC or CBD, just terpenes.  Our Broad Spectrum Effect line is built entirely with our isolated terpenes and designed to represent the specific effect that they are named after. Utilizing only the finest, hand selected terpenes, these blends deliver the desired effect consistently.

Disclaimer:

Extract Consultants does not sell any products with THC and/or CBD.  Special care should be taken to ensure safety at all times.  Please wear gloves and eye protection and have proper ventilation.  Our products are extremely potent and concentrated. For more safety Information, please review each materials SDS (safety data sheet.)

 

Product data sheets can be found here.

Extract Consultant’s line of terpene blends are specifically designed to work directly with oil or distillate. End products are primarily carts and tinctures. Each terpene blend has an average add back range of .5%-3%. This can vary quite a bit based on preference, so our general rule of thumb is always start low and work your way up. You can always add more! 

Step 1 – Prepare your material and Calculate add back rate.

  • Warm up your distillate or oil as you normally would.
  • Calculate how much terpenes you will need to use by weight. Always measure by weight, and never by the drop. We will use an example of a 50g batch, and an add back rate of 3%. Using a calculator, input 50 X 0.03 (3%.) You should get an answer of 1.5g.

Step 2 – Weigh your terpenes and set aside in preparation for mixing.

  • Next, take a Pyrex beaker and a scale that is accurate to at least 0.00 decimal places. Place beaker on the scale and using the same example of 3% usage in a 50g batch, carefully weigh out 1.5g of terpenes, using a disposable plastic pipette.
  • Set aside in preparation for mixing.

Step 3 – Remove distillate or oil from heat and allow it to cool.

  • Let your material cool down enough so that you can still manipulate it. Distillate and oil should at the very most be 100°F at the time of adding terpenes.

Step 4. Add and mix.

  • Once your material is at 100°F or less, it is time to add back the 1.5g of terpenes. Poor them into the distillate or co2 oil and using either a Magnetic Stir bar or a hand tool, mix the solution for up to 20min.

Step 5. Wait, and taste.

  • Many people make the mistake of tasting the product right after mixing. It is always better to let the solution sit for 24 hours. Once it has steeped for a day, and it has passed your visual test, you may apply it to whichever end product the material is going into and give it an official taste test.

Step 6. Record your formula, and move to production

  • Once you are satisfied with your end product, it is ready to go into production. If this is the first time you have developed this product, be sure to document your add back rate for each terpene product for future use.

Note: Always store your finished product between 60° and 75°. This will help prevent separation, crystallization, and oxidation.

 

Easy to use instructions for how to add flavors to concentrates!  We have included an abbreviated PDF version of these instructions for your convenience. Also included in this download is a worksheet to keep track of the add back rate you use for each of your products!

Recreation Terpene Effect Blend

$10.00