Extract Consultant’s line of terpene blends are specifically designed to work directly with oil or distillate. End products are primarily carts and tinctures. Each terpene blend has an average add back range of .5%-3%. This can vary quite a bit based on preference, so our general rule of thumb is always start low and work your way up. You can always add more! 

Step 1 – Prepare your material and Calculate add back rate.

• Warm up your distillate or oil as you normally would.
• Calculate how much terpenes you will need to use by weight. Always measure by weight, and never by the drop. We will use an example of a 50g batch, and an add back rate of 3%. Using a calculator, input 50 X 0.03 (3%.) You should get an answer of 1.5g.

Step 2 – Weigh your terpenes and set aside in preparation for mixing.

• Next, take a Pyrex beaker and a scale that is accurate to at least 0.00 decimal places. Place beaker on the scale and using the same example of 3% usage in a 50g batch, carefully weigh out 1.5g of terpenes, using a disposable plastic pipette.
• Set aside in preparation for mixing.

Step 3 – Remove distillate or oil from heat and allow it to cool.

• Let your material cool down enough so that you can still manipulate it. Distillate and oil should at the very most be 100°F at the time of adding terpenes.

Step 4. Add and mix.

• Once your material is at 100°F or less, it is time to add back the 1.5g of terpenes. Poor them into the distillate or co2 oil and using either a Magnetic Stir bar or a hand tool, mix the solution for up to 20min.

Step 5. Wait, and taste.

• Many people make the mistake of tasting the product right after mixing. It is always better to let the solution sit for 24 hours. Once it has steeped for a day, and it has passed your visual test, you may apply it to whichever end product the material is going into and give it an official taste test.

Step 6. Record your formula, and move to production

• Once you are satisfied with your end product, it is ready to go into production. If this is the first time you have developed this product, be sure to document your add back rate for each terpene product for future use.

Note: Always store your finished product between 60° and 75°. This will help prevent separation, crystallization, and oxidation.

We have included an abbreviated PDF version of these instructions for your convenience. Also included in this download is a worksheet to keep track of the add back rate you use for each of your products!

Disclaimer:

Extract Consultants does not sell any products with THC and/or CBD.  Special care should be taken to ensure safety at all times.  Please wear gloves and eye protection and have proper ventilation.  Our products are extremely potent and concentrated. For more safety Information, please review each materials SDS (safety data sheet.)

Product data sheets can be found here.

Mango Kush is a hybrid strain prized for its potent tropical flavors and body effects. Our Mango Kush terpene profile has strong mango and sweet tropical flavors with prominent notes of kushy pine. As a universal flavor should be, it is sure to fit well on anyone’s shelf.

Our team of chemists and formulators worked hard to recreate this strain's terpene profile, giving you a repeatable and controlled effect every single time. To create this blend, we've used the following key terpenes. This is only a partial list of the blend's formulation; each blend actually contains far more isolates.

Myrcene, Pinene, Humulene, Alpha Bisabolol, Linalool

Our Solvent Free Terpene Blends are derived from high quality, individual isolated terpenes. These organic terpenes are extracted from natural plant sources using plant analytics to recreate terpene profiles and flower-like effect. These terpene blends are designed specifically for customers who want to remain solvent free. They do not contain THC or CBD, just terpenes.

• No PG
• No MCT Oil
• All Natural
• Non-GMO
• GRAS
• Food Grade Certified

Extract Consultant’s line of terpene blends are specifically designed to work directly with oil or distillate. End products are primarily carts and tinctures. Each terpene blend has an average add back range of .5%-3%. This can vary quite a bit based on preference, so our general rule of thumb is always start low and work your way up. You can always add more! 

Step 1 – Prepare your material and Calculate add back rate.

• Warm up your distillate or oil as you normally would.
• Calculate how much terpenes you will need to use by weight. Always measure by weight, and never by the drop. We will use an example of a 50g batch, and an add back rate of 3%. Using a calculator, input 50 X 0.03 (3%.) You should get an answer of 1.5g.

Step 2 – Weigh your terpenes and set aside in preparation for mixing.

• Next, take a Pyrex beaker and a scale that is accurate to at least 0.00 decimal places. Place beaker on the scale and using the same example of 3% usage in a 50g batch, carefully weigh out 1.5g of terpenes, using a disposable plastic pipette.
• Set aside in preparation for mixing.

Step 3 – Remove distillate or oil from heat and allow it to cool.

• Let your material cool down enough so that you can still manipulate it. Distillate and oil should at the very most be 100°F at the time of adding terpenes.

Step 4. Add and mix.

• Once your material is at 100°F or less, it is time to add back the 1.5g of terpenes. Poor them into the distillate or co2 oil and using either a Magnetic Stir bar or a hand tool, mix the solution for up to 20min.

Step 5. Wait, and taste.

• Many people make the mistake of tasting the product right after mixing. It is always better to let the solution sit for 24 hours. Once it has steeped for a day, and it has passed your visual test, you may apply it to whichever end product the material is going into and give it an official taste test.

Step 6. Record your formula, and move to production

• Once you are satisfied with your end product, it is ready to go into production. If this is the first time you have developed this product, be sure to document your add back rate for each terpene product for future use.

Note: Always store your finished product between 60° and 75°. This will help prevent separation, crystallization, and oxidation.

 

We have included an abbreviated PDF version of these instructions for your convenience. Also included in this download is a worksheet to keep track of the add back rate you use for each of your products!

Liquid error (product-description line 104): Cannot render sections inside sections

• FGC
• SDS
• TDS